What Information Should Be Included in a Lighting Profile Drawing?

Most tooling rework traces back to one of four missing items on the drawing: the optical requirement, the colour standard, the critical dimensions, or the compliance environment. This is the checklist that prevents all four.

Search intent

Checklist intent. Engineers preparing a drawing package for quotation who want to avoid the back-and-forth that delays tooling.

The essentials – without these, no quote

  1. Cross-section drawing – DXF, DWG, STEP or a fully dimensioned PDF. It must be the true cross-section, not an assembly view.
  2. Annual quantity – drives tooling amortisation, line scheduling and the material price bracket.
  3. Material – PC or PMMA. If undecided, state the application and compliance requirement and let the supplier propose.

Geometry and tolerances

Geometric information
Full cross-sectionAll walls, ribs, radii and channels, dimensioned
Wall thicknessesExplicit, and nominally uniform within about 2:1
Corner radiiShown, including at snap-fit roots
Critical dimensionsMarked – the ones that mate with another part
General toleranceEverything else left to standard extrusion tolerance
Length and cut toleranceCut length, plus/minus, and squareness requirement
Straightness / bowIf the run length makes it matter, state it
Section weightOptional; helps convert quantity into material mass

Typical achievable tolerance for PC and PMMA lighting sections is roughly +/- 0.15 mm to +/- 0.30 mm on features up to about 60 mm when the die and calibrator are matched to the section. Marking every dimension tighter does not improve fit – it raises cost.

Material specification

  • Base polymer – PC or PMMA.
  • Grade requirement – UV-stabilised, flame-retardant, impact-modified, or general purpose.
  • Flame rating – UL94 class, if the fixture must comply.
  • Compliance documentation – UL, RoHS, REACH as needed.
  • Recycled content requirement, if any.

Optical specification

This is the item most often missing, and the one most likely to cause a second sampling round. A material name is not an optical specification. State:

  • Transmission target, or maximum acceptable lumen loss.
  • Haze level, if known.
  • LED pitch, board width, and standoff distance to the optical surface.
  • Viewing angles at which hotspots must not be visible.
  • For lens or prismatic profiles: the target beam distribution.
  • Acceptable colour shift across the visible surface.

If you do not know the haze level, describe the requirement in geometry – “hide a 10 mm LED pitch at 20 mm standoff at normal viewing” – and let the supplier propose the material package. See how to develop a custom LED diffuser profile.

Colour and surface

Appearance information
ColourRAL or Pantone reference, or a signed-off physical sample
Gloss levelHigh gloss, satin, matt
TextureFine frost, prismatic, or a specified surface pattern
Surface defectsAcceptable level of die lines, and on which faces
Visible facesMark which surfaces are seen in the finished fixture

Marking the visible faces is worth the ten seconds it takes. It tells the extruder where surface quality matters and where it does not, which affects die finishing and handling.

Application and environment

  • Where the profile is used – linear, architectural, industrial, troffer, office, signage or other.
  • Indoor or outdoor – decides UV-stabilised grades.
  • Service temperature range.
  • Chemical exposures – cleaning agents, adhesives, gasket materials.
  • Impact requirement or IK rating.
  • IP rating, if the fixture is sealed.

Chemical exposure matters more than buyers expect. Both PC and PMMA craze or crack in contact with certain adhesives and solvents, and the fix is a grade or adhesive change at specification stage – not a field failure later.

Assembly and secondary operations

  • Mating parts – board width and tolerance, end-cap geometry, fixing method.
  • Secondary operations – drilling, punching, notching, printing, and where they fall.
  • Sealing method if an IP rating is required – co-extruded lip or gasket groove.
  • Packing – cut length, sleeving, bundling, palletising.

One-page checklist

Drawing package checklist
[ ]Cross-section drawing, dimensioned, DXF/DWG/STEP/PDF
[ ]Annual quantity and order pattern
[ ]Material and grade
[ ]Optical requirement – transmission, haze, or geometry-based target
[ ]LED pitch and standoff distance
[ ]Colour standard and gloss level
[ ]Critical dimensions marked; general tolerance stated
[ ]Cut length and tolerance
[ ]Application, environment and compliance requirements
[ ]Mating part geometry and secondary operations
[ ]Packing requirement

Missing items are not blockers. Send what you have – the cross-section and the annual quantity are enough to start – and the rest can be resolved during the feasibility review.

Send the drawing: request a quote. See also custom lighting extrusion from drawing to production.

Steel extrusion die with locating pins ready for fitting to the extruder
Every marked dimension on the drawing becomes a measurement at the die. An unmarked drawing is an expensive drawing.

Which lines on the drawing carry the most weight

Not all dimensions cost the same. When a drawing arrives, we read it in this order, because this is the order in which missing information delays a quote.

ItemWeight in the quoteWhat happens if it is missing
Marked critical dimensionsHighestEvery supplier assumes a different precision; the quotes are not comparable
Material and gradeHighPMMA and PC differ in processing window, so tooling and scrap change
Wall thickness and uniformityHighThe die cannot be flow-balanced; expect correction passes
Optical target stated as a numberMedium-high"Prismatic" is not a specification; the first article cannot be accepted or rejected
Colour reference (RAL / Pantone / sample)MediumColour is matched by eye, then disputed at the batch
Mating surfaces and assemblyMediumThe section fits on paper and not in the fixture
Annual quantityLow for tooling, high for adviceYou get a single-strand die when a multi-strand would have halved the piece price

Four things drawings usually leave out

Which side faces the LED

A prism surface put on the wrong face changes both the distribution and the visible sparkle. One arrow on the section removes the ambiguity.

The end condition

Cut square, cut to length with a chamfer, or not cut at all. Cutting is a secondary operation with its own tolerance and its own cost line.

Whether the part is visible

A surface that will be seen needs a cosmetic standard. A hidden housing surface does not, and paying cosmetic tolerance on it is pure waste.

The revision the sample was made to

Projects stall when a sample matches rev B and the drawing has moved to rev C. Put the revision on the sample bag.

What we do with a drawing that is not complete

We quote it with the gaps named, rather than filling them silently. If the critical dimensions are unmarked we will say so and ask; if the material is unspecified we will state which one we assumed and why. A provisional quote with three open questions is more useful than a firm number built on assumptions you did not see.

Frequently asked questions

DXF, DWG or STEP are ideal; a fully dimensioned PDF is fine. What matters is that it is the true cross-section with dimensions, not an assembly or isometric view.
Yes, if the profile is optical – and a material name is not an optical specification. State transmission, haze, or the geometry (LED pitch and standoff) and let the supplier propose the package.
Mark the dimensions that mate with another part, typically +/- 0.15 to 0.30 mm. Leave everything else to general extrusion tolerance; tighter callouts on non-critical dimensions raise cost without improving fit.
State the application and the compliance requirement instead – impact, flame rating, UV exposure, service temperature. The material normally follows from those answers.
Yes – it drives tooling amortisation, scheduling and material pricing, and it changes the quote more than most geometric details.

Yes, if the section is fully dimensioned. A PDF is enough for most linear profiles. A DXF or DWG is better where the section has splines or a prism geometry that has to be measured rather than read.

Something explicit – a general note plus marked criticals. We work to ±0.1 mm on marked critical die dimensions; the rest follows the general note. A drawing with no general note and no marked criticals is the one case where we cannot give a firm tooling figure.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top