Industrial Lighting Profiles

Polycarbonate and PMMA profiles for factories, warehouses and harsh environments – covers and housings that take impact, heat and dust.

What this application demands from the profile

Industrial lighting is specified by what the fitting has to survive: impact from tools and vehicles, vibration, dust, moisture, cleaning chemicals and heat from high-power boards. Material choice follows from that list, and it usually points to polycarbonate.

Wall thickness, sealing geometry and fixing method matter more than they do in commercial work, and the profile is often the part that determines the fitting’s IP rating and impact class.

Industrial lighting profiles - what we supply
Luminaire typeFactory, warehouse, logistics and harsh-environment luminaires
Profile roleImpact-resistant cover, housing or sealing section
MaterialsPC for impact and heat; PMMA where transmission is the priority
Wall thicknessSet to the impact requirement of the fitting
EnvironmentUV-stabilised and flame-retardant grades available
SealingGeometry designed around your gasket and IP requirement
Typical fittingsHigh-bay, low-bay, tri-proof and bulkhead luminaires

What we work to

Industrial lighting profile - capability envelope
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Wall thicknessquoted against your drawing - heavy sections run
Transmittance0-97%
FlammabilityUL94 V-0 from 1.0 mm, V-2 down to 0.40 mm - material grade
IngressIP65 / IP66 / IP67 achieved by section and gasket design, not by the material
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Industrial work is specified by what the fitting has to survive. The flame rating above is a property of the material grade at a stated thickness – it is not a certification of the finished luminaire.

What industrial lighting asks of a profile

Industrial fittings are specified by their environment before their optics: impact, dust, water, chemicals, temperature, and in some sectors a flame rating. Write the environment down at quotation stage and most of the material question answers itself. Leave it out and the selection is made on optics, which is usually the wrong reason in a factory.

Polycarbonate is the common answer here, for impact resistance and for heat. Where a flame rating is required, the grades we run reach UL94 V-0 from 1.0 mm and V-2 down to 0.40 mm – and it is worth being precise about what that means: it is a material property at a stated thickness, not an approval of the finished fitting. Compliance for the luminaire is assessed at fixture level.

Ingress protection is a design result, not a material property. IP65, IP66 and IP67 are achieved by the section, the gasket groove and the end-cap arrangement working together. If the drawing shows the section but not the gasket interface, the rating cannot be quoted – it can only be tested.

Heat and chemicals finish the list. A high-bay fitting puts real temperature into the cover, and cleaning regimes in food and pharmaceutical plants use agents that attack some polymers. Tell us both and the grade selection is straightforward; guess at either and the cover fails in service rather than in test.

What to put on the drawing

  • Environment: impact, dust, water, temperature, cleaning agents
  • Required IP rating and the gasket interface that delivers it
  • Flame rating required – and whether it is grade-level or fixture-level
  • Section at 1:1 with wall thickness dimensioned separately
  • Transmittance target as a number, plus surface finish
  • Cut length, packing and annual volume

Where an industrial profile goes wrong

Four failures account for most industrial covers that come back, and all four are environment mistakes rather than extrusion mistakes.

Flame rating treated as a finished-part approval

UL94 belongs to the material at a stated thickness. It is not a certification of the luminaire, and treating it as one fails at compliance review.

IP rating quoted without a gasket design

Ingress protection comes from the section and the seal working together. Without the gasket interface on the drawing, the rating cannot be engineered - only tested.

Cleaning agent attacking the polymer

Some industrial cleaners and gasket materials stress-crack polycarbonate. The cleaning regime belongs in the specification.

Heat ignored in a high-bay fitting

A cover that runs hot creeps. PC holds shape at temperatures where PMMA moves, which is why the operating temperature decides the material.

Industrial profiles fail in service, not in goods-in. That makes the environment section of your enquiry the most valuable paragraph in it.

Profile requirements

  • Impact-resistant covers that survive tools, vehicles and vibration
  • Material that holds up at the operating temperature of the fitting
  • Wall thickness matched to the impact class
  • Sealing geometry designed around the gasket and IP rating
  • Flame-retardant grades where the specification requires them
  • UV-stabilised grades where fittings see daylight or exterior use

Frequently Asked Questions

Impact. Industrial fittings are struck and vibrated, and PC survives where acrylic cracks. The higher service temperature also matters near high-power LED boards.
Yes. FR grades are available where the luminaire specification requires them – specify early because it affects material sourcing and lead time.
The profile is part of the sealing system. Send the gasket detail and the target IP rating and we design the section geometry around it.
Polycarbonate in most cases – impact and heat. PMMA where transmission and colour stability matter more than toughness.
The grades we run reach UL94 V-0 from 1.0 mm and V-2 down to 0.40 mm. That is the material grade at a stated thickness, not a certification of your finished fitting.
We extrude the profile to the section that makes the rating achievable. The rating itself is verified on the assembled fitting, and the gasket interface has to be on the drawing.
From 500 pcs per profile, around six weeks from drawing to production including tooling.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top