PC Lighting Profiles

Polycarbonate lighting extrusion profiles for covers, housings and fittings where impact strength and heat resistance decide the material.

What we supply

Polycarbonate is chosen when the profile has to survive impact. Vandal-resistant fittings, industrial luminaires, warehouse and parking-garage fixtures, and any cover that can be struck or dropped – these are PC jobs, not PMMA jobs.

PC also carries a higher continuous service temperature than acrylic, which matters when the profile sits close to a high-power LED board. The trade-off is slightly lower transmission and a material that is more sensitive to processing, so wall thickness and die design need more care.

PC lighting profile - material and capability
MaterialPolycarbonate (PC), UV-stabilised grades available
Key advantageVery high impact resistance and heat resistance
Typical useLight covers, housings, tri-proof and industrial fittings
SurfaceClear, matte, frosted, embossed or prismatic
ColourClear, opal, or matched to RAL / Pantone
ProcessSingle-material and co-extrusion
Flame retardancyFR grades available on request
LengthCut to length to your specification

What we work to

PC lighting profile - capability envelope
Materialpolycarbonate, UV-stabilised grades available
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Wall thicknessquoted against your drawing
Transmittance0-97%
FlammabilityUL94 V-0 from 1.0 mm, V-2 down to 0.40 mm - material grade
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Polycarbonate is specified for what it survives, not for how it looks. The flame rating above is a property of the material grade, not a certification of the finished profile – compliance for the luminaire is assessed at fixture level.

How to specify a PC lighting profile

PC is the default when the part can be hit. Impact resistance is the reason it is used for low-mounted covers, for transport and rail interiors, and for anything within reach of a trolley or a ladder. It also holds its shape at temperatures where PMMA starts to soften, which makes it the safer choice where the profile doubles as a heat path for the LED.

The cost of that toughness is optical. Polycarbonate transmits slightly less light in the visible range than acrylic, and unstabilised grades drift towards yellow under UV faster. Where a fixture is judged on light output first, that gap is the whole argument. Where it is judged on surviving ten years of cleaning and knocks, PC wins on the first page.

Flammability is the other reason PC gets specified. The grades we run reach UL94 V-0 from 1.0 mm and V-2 down to 0.40 mm. Be clear whether you are specifying the material grade or a finished-part approval – they are different documents and only the second one covers the luminaire.

On the drawing, PC lets you be more aggressive with snap geometry than acrylic does, but it is not unlimited. Give us the wall thickness at the snap, the deflection you need during assembly, and the transmittance target, and we will check the undercut before the die is cut rather than after the first crack appears.

What to put on the drawing

  • Section at 1:1 with wall thickness dimensioned separately
  • Impact requirement: what the part has to survive, and how it is tested
  • Flame rating required, and whether it is grade-level or fixture-level
  • Transmittance target as a number, plus surface finish
  • UV exposure: indoor, outdoor, or behind glass
  • Cut length, packing and annual volume

Where a PC profile goes wrong

Four failures account for most of the polycarbonate parts that come back, and three of them are material-selection mistakes rather than extrusion mistakes.

UV drift mistaken for a resin fault

Unstabilised PC yellows under UV. If the fixture sits in daylight, the grade has to be specified for it - the extrusion process cannot fix a grade that was never chosen for the exposure.

Stress cracking from the wrong cleaner or adhesive

Polycarbonate is sensitive to certain solvents and to some gasket materials. A cover that cracks in service has often been cracked by what was used to clean or seal it.

Flame rating assumed at part level

A UL94 rating belongs to the material at a stated thickness. It is not a certification of the finished luminaire, and treating it as one is the fastest route to a failed compliance review.

Optical loss ignored in the photometric plan

PC transmits less than PMMA. If the photometric calculation was done for acrylic and the part was switched to PC for impact, the fixture comes out dimmer than the spec sheet.

Every one of these is cheaper to settle before tooling. Send the exposure conditions and the compliance requirement with the drawing and the material question answers itself.

Options we build into the profile

  • UV-stabilised PC for exterior and semi-exterior luminaires
  • Flame-retardant grades where the fitting requires it
  • Co-extruded PC with a diffusing PMMA layer
  • Thick-wall sections for high-impact covers
  • Prismatic surface for glare control
  • Cutting, drilling and machining to your assembly drawing

Frequently Asked Questions

Choose PC when the profile can be struck, when it sits close to a hot LED board, or when the fitting needs flame-retardant material. Choose PMMA when maximum transmission and UV stability matter more than impact.
Standard PC weathers less well than PMMA. For exterior use we run UV-stabilised PC grades, which is why we ask about the installation environment early.
Yes. A common construction is a PC body for strength with a PMMA diffusing layer for optical performance.
PC when the part has to survive impact, heat or a flame rating. PMMA when transmission and long-term colour stability come first. Where both matter, co-extrusion puts a PMMA optical face on a PC body.
The grades we run reach UL94 V-0 from 1.0 mm and V-2 down to 0.40 mm. That is a material property at a stated thickness, not a certification of your finished fixture.
Unstabilised grades do, particularly under UV. Stabilised grades and co-extruded UV caps hold colour far longer. Which one you need depends on where the fixture is installed.
±0.1 mm on the dimensions that carry the fit. Optical geometry such as prisms is held by die condition and maintenance intervals rather than by the tolerance callout.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top