Lighting Tubes

PC and PMMA tubes and tube profiles for LED tube luminaires, linear fixtures and protective sleeves – extruded and cut to your length.

What we supply

Tube is the simplest section to describe and one of the harder ones to hold: roundness, wall consistency and straightness all have to stay controlled along the length, and thin walls on a large diameter are the difficult combination.

We extrude tubes in PC and PMMA – clear, opal or frosted – to the diameter and wall thickness your fitting needs, and cut to length for your assembly line.

Lighting tube - capability
FormRound tube, half-round, oval and custom tubular sections
MaterialsPC and PMMA; UV-stabilised grades available
FinishClear, opal, frosted, matte
Wall thicknessTo your specification - reviewed for extrudability
DimensionsDiameter and wall to your drawing
LengthCut to length to your specification
Typical useLED tube luminaires, protective sleeves, linear fixtures
PackingProtective film, bundles and cartons to your specification

What we work to

LED tube cover and housing - capability envelope
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Wall thicknessquoted against your drawing
Transmittance0-97%
FlammabilityUL94 V-0 from 1.0 mm, V-2 down to 0.40 mm - material grade
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Tube covers are quoted to your diameter, wall and end-cap interface, not to a T-size. If you are replacing an existing tube, send the part – the nominal size rarely matches the actual section.

How to specify an LED tube cover

A tube cover is a simple part with an unforgiving job: it has to pass light evenly around a semi-circle, hide the LED board behind it, and fit the end caps that somebody else moulded. The first two are optical decisions; the third is a tolerance decision, and it is the one that most often fails.

Retrofit work is where this shows up. A T8 or T5 nominal size describes a lamp standard, not an extrusion section, and the covers on the market differ in diameter, wall and clip detail. If you are replacing an existing tube, the fastest route is a cut length of the part you are using: we measure the section, confirm the material, and quote against the real geometry rather than the nominal size.

Material follows the usual split. PMMA for transmission and colour stability; PC where the tube can be struck, where the driver runs hot, or where a flame rating is required at a thin wall. For transport and industrial fittings, PC is the common answer; for office and retail, PMMA usually wins on light output.

On the drawing, call out the outside diameter and the wall separately, the end-cap interface and which dimension it lands on, and the transmittance target at that wall. Add how the tube is supported along its length – an unsupported thin cover in a hot fixture will bow, and the bow shows as a bright line down the tube.

What to put on the drawing

  • Outside diameter and wall thickness, dimensioned separately
  • End-cap interface and the dimension it lands on
  • Transmittance target as a number at that wall thickness
  • Support spacing along the tube length
  • Operating temperature and any flame rating required
  • Cut length, packing and annual volume

Where a tube cover goes wrong

Four failures account for most of the tube covers that come back, and two of them are about the end caps rather than the extrusion.

End caps that fit the sample and not the run

The cap lands on one dimension. If that dimension is not marked as critical, the fit varies across the run and the failure appears on your assembly line.

Bow in a hot fixture

A thin unsupported cover in a warm fitting creeps. Support spacing belongs on the drawing as much as the section does.

Visible LED board through the cover

Transmission is not diffusion. Hiding the board depends on transmission, wall thickness and the distance to the LEDs together.

Nominal size assumed instead of measured

T-sizes describe lamps, not extrusion sections. Covers that share a nominal size rarely share a section.

Tube covers are cheap parts that fail expensively, because the failure appears at assembly rather than at goods-in. Mark the cap interface as critical and send a sample if one exists.

Options we build into the profile

  • Clear, opal and frosted finishes for different diffusion needs
  • UV-stabilised grades for exterior tube applications
  • Tight control of roundness and wall consistency
  • Half-round and oval sections for surface-mounted fixtures
  • Cutting, drilling and end preparation
  • Protective film to keep surfaces clean through assembly

Frequently Asked Questions

Tube dimensions are set by the tooling. Send the diameter and wall you need and we confirm what is practical for stable extrusion, or propose the closest workable section.
Yes. Tube for LED tube luminaires is one of the common applications, supplied cut to length and packed for assembly.
Yes. Clear, opal and frosted finishes are available in both PC and PMMA.
We make them to your section rather than to a nominal size. If you are replacing an existing tube, send a cut length and we will quote against the measured geometry.
PMMA for maximum light output and colour stability; PC where the tube can be struck, runs hot, or needs a flame rating at a thin wall.
Yes. A co-extruded profile can carry an optical face and an opaque or structural section in the same pass, which is the usual way to hide fixings and cabling.
From 500 pcs per profile. Below that the changeover and first-off checking dominate the cost.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top