Linear Lighting Profiles

Continuous extruded sections for linear luminaires – diffusers, housings and combined profiles cut to the length your system needs.

What this application demands from the profile

Linear lighting is the application that suits extrusion best: the profile runs continuously, cost per metre stays low, and a single section can carry the diffuser, the housing and the fixing geometry at once.

It is also the application that exposes extrusion quality fastest. A section that bows or twists is obvious across a six-metre run, colour variation between batches shows as a visible band, and a badly cut length puts the joint in the wrong place.

Linear lighting profiles - what we supply
Luminaire typeLinear luminaires, suspended and surface systems, continuous runs
Profile roleDiffuser, housing, or a combined co-extruded section
MaterialsPMMA for transmission, PC for impact, PC/PMMA co-extrusion
SurfaceClear, opal, frosted, matte or prismatic
LengthCut to length - standard fixture lengths or to your specification
Key controlsStraightness, twist, colour consistency between batches
AssemblyClip, slide-in or screw-fix geometry extruded into the section

What we work to

Linear lighting profile - capability envelope
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Wall thicknessquoted against your drawing
Transmittance0-97%
Surfaceclear, matte, frosted, embossed or prismatic
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Linear systems are judged along the length, not at the cross-section. Straightness, joint detail and how the light behaves at the seam decide whether a run reads as continuous.

What linear lighting asks of a profile

Linear lighting is the natural fit for extrusion: the section stays constant and the length is whatever the building needs. It is also where the expensive failures hide. A run can measure perfectly at every cut end and still look wrong when it is switched on, because what the eye reads is continuity – the seam between lengths, the shadow at a corner, the falloff where one profile ends.

Two numbers decide whether a linear run reads as a line or as a row of dots: the LED pitch and the distance from the strip to the optical face. Transmission alone does not settle it. A cover that reads 85% on a sample card will still hotspot if it sits too close to the board. Send the pitch and the gap with the drawing and the diffusion can be sized to them.

The mechanical half is support. A thin cover clipped at long intervals bows under its own weight, and the bow shows as a shadow line down the run. Clip spacing belongs on the drawing with the section, not in the installation instructions.

For continuous runs, specify cut-length tolerance and end squareness. Half a millimetre per joint is invisible on a sample and obvious over a corridor, and it is far cheaper to specify than to shim on site.

What to put on the drawing

  • Section at 1:1 with clip positions and spacing
  • LED pitch and distance from strip to optical face
  • Joint detail, cut-length tolerance and end squareness
  • Transmittance target as a number, plus surface finish
  • Glare target if the space is worked in – UGR
  • Cut length, packing and annual volume

Where a linear run goes wrong

Four failures account for most of the linear installations that get complained about, and all four only appear once the run is lit and installed.

Hotspots along the LED pitch

Transmission is not diffusion. Too wide a pitch or too small a gap and the run reads as dots, whatever the material is.

Bow between clips

Thin covers sag between fixings. The sag shows as a shadow line, and the fix is clip spacing on the drawing.

Visible joints on a long run

Cut-length tolerance accumulates. Over a corridor, a small error at each joint becomes a visible step.

Glare missed until handover

Linear runs over workstations fail on UGR, not on output. The optical surface has to be chosen against the glare target.

These are installation-visible failures, which is why we ask for pitch, clip spacing and joint detail at quotation stage rather than at first-off.

Profile requirements

  • Sections that extrude straight and stay straight over long lengths
  • Diffusion tuned to hide LED pitch at a defined transmittance
  • Colour matched across production batches for phased projects
  • Accurate cutting so joints land where the design intends
  • Prismatic surfaces where glare control is part of the specification
  • Combined diffuser and housing sections to remove assembly steps

Frequently Asked Questions

Visible joints are controlled two ways: consistent section geometry so ends match, and accurate cutting. We can also design the section so the joint falls into a shadow line.
We control colour batch to batch. For long or phased projects tell us at the start so material can be reserved and the match kept consistent.
Yes – co-extrusion runs an opaque housing zone and a diffusing zone in one section, which removes a part and an assembly step.
Cut to your specified length from continuous extrusion. Give us the length, the tolerance and the joint detail and we quote to that.
Fix the LED pitch and the strip-to-cover distance first, then choose transmission to suit them.
Yes – co-extrusion puts an opaque or structural body and an optical face in the same pass, which is the usual way to hide fixings in a visible run.
From 500 pcs per profile, with around six weeks from drawing to production including tooling.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top