Materials for Lighting Extrusion

Polycarbonate and PMMA – the two materials that cover almost every lighting profile, and how to choose between them.

What we work to

Optical materials - capability envelope
Materials runpolycarbonate and PMMA, including UV-stabilised grades
Single or co-extrudedboth - two materials in one pass down one die
Transmittance0-97%, tuned to the target rather than to a default
FlammabilityUL94 V-0 from 1.0 mm, V-2 down to 0.40 mm - material grade
UV stabilitystabilised grades and co-extruded UV caps available
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Material selection is not a preference, it is a consequence. Impact, heat, exposure and compliance decide it, and the flame rating above is a property of the grade – not a certification of the finished luminaire.

How to choose between PC and PMMA

Every lighting profile we run is polycarbonate or PMMA, and the choice between them is settled by four questions: can it be hit, does it run hot, what is it exposed to, and what does the compliance file require.

Polycarbonate is the answer to the first and the last. It survives impact that cracks acrylic, it holds shape at temperatures where PMMA moves, and the grades we run reach UL94 V-0 from 1.0 mm and V-2 down to 0.40 mm. Its cost is optical: it transmits slightly less in the visible range, and unstabilised grades drift towards yellow under UV.

PMMA is the answer when light and colour come first. It transmits more than PC, it is among the most UV-stable optical plastics available, and it replicates fine prism geometry more cleanly – which is why prismatic diffusers and linear lenses are usually quoted in acrylic. Its cost is toughness: it is the more brittle material, and it loses impact strength as temperature drops.

When one section needs both, co-extrusion is the usual resolution: a PMMA optical face on a PC structural body, bonded in one pass. It costs more in tooling and in first-off checking, and it removes a secondary assembly step on your line.

What to put on the drawing

  • Impact requirement – what the part has to survive, and how it is tested
  • Operating temperature, and whether the profile is a heat path
  • Exposure: indoor, outdoor, behind glass, and service life
  • Compliance requirement – and whether it is grade-level or fixture-level
  • Transmittance target as a number at the running wall thickness
  • Colour reference – RAL, Pantone or a physical chip

Where material selection goes wrong

Four mistakes account for most of the material changes that get made after sampling, and all four come from answering the questions in the wrong order.

Optics chosen before environment

A material picked for transmission alone will fail in a fitting that gets hit, runs hot, or sits in sun. Environment first, optics second.

Flame rating treated as a finished-part approval

UL94 belongs to the material at a stated thickness. It is not a certification of the luminaire.

UV exposure not stated

Stabilised grades and UV-capped co-extrusions cost more than standard grades. Without the exposure on the enquiry, the cheaper one gets quoted.

Material switched without rechecking the optics

Moving a part from PMMA to PC changes transmission. If the photometric plan was done for acrylic, the fixture comes out dimmer than specified.

Material is the one decision that cannot be corrected after tooling. Send the environment and the compliance requirement with the drawing.

Questions we get asked

Which transmits more light - PC or PMMA?

PMMA. It transmits more in the visible range and holds that transmission longer under UV.

Which is more impact resistant?

Polycarbonate, by a wide margin. That is why it is specified for low-mounted and transport fittings.

Can I have both?

Yes - co-extrusion runs a PMMA optical face on a PC structural body in a single pass.

What flame rating do you run?

Grades reaching UL94 V-0 from 1.0 mm and V-2 down to 0.40 mm. That is the material grade at a stated thickness, not a certification of your finished fitting.

Scroll to Top