Linear Light Profiles

Continuous extruded sections for linear luminaires – runs, coves, suspended systems and architectural lines, cut to the length your fixture needs.

What we supply

Linear lighting is where extrusion shows its advantage: the profile is continuous, the cost per metre is low, and the section can carry the diffuser, the housing and the fixing geometry in one piece. Long runs also expose problems – bow, twist, colour variation between batches and visible joints.

We design the section so it extrudes straight and stays straight, control colour batch to batch, and cut to the length your assembly line needs so joints land where you want them.

Linear light profile - capability
ApplicationLinear luminaires, coves, suspended and surface systems
MaterialsPMMA, PC, PC/PMMA co-extrusion
SectionDiffuser, housing, U-channel, or combined
LengthCut to length - standard fixture lengths or your specification
StraightnessSection designed and calibrated for stable long runs
SurfaceClear, matte, frosted, prismatic
JoiningGeometry can be designed to disguise joints between lengths
Colour controlMatched between batches for continuous runs

What we work to

Linear light profile - capability envelope
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Wall thicknessquoted against your drawing
Transmittance0-97%
Surfaceclear, matte, frosted, embossed or prismatic
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

A linear profile is judged along its length, not at a cross-section. Straightness, twist and the way light behaves at the joints decide whether a run looks continuous – and none of those appear on a section drawing.

How to specify a linear light profile

Linear lighting is where extrusion earns its keep: the section stays constant and the length is whatever the building needs. It is also where the failure modes are least visible on paper. A run can be dimensionally perfect at every cut end and still look wrong when it is lit, because what the eye reads is continuity – the seam between two lengths, the shadow at a corner, the falloff where one profile ends and the next begins.

The section has to carry three things that are rarely drawn: how the cover clips in and how much it bows between clips, how the LED strip is positioned relative to the optical face, and what happens at the joint. Send those and the rest of the geometry follows. Leave them out and the first-off will fit and the installation will not.

Diffusion is the other half. In a linear fixture the LED pitch and the distance from the strip to the cover decide whether you see a row of dots or a continuous line. Transmission alone does not tell you that – a cover that reads 85% on a sample can still hotspot if it sits too close to the strip. Give us the pitch and the gap and we will size the diffusion to it.

For continuous runs, ask for cut-length tolerance and joint detail on the drawing rather than inheriting them. A gap of half a millimetre per joint accumulates over a corridor, and it is far cheaper to specify than to shim on site.

What to put on the drawing

  • Section at 1:1, with clip positions and bow between clips
  • LED pitch and the distance from strip to optical face
  • Joint detail and cut-length tolerance for continuous runs
  • Transmittance target as a number, plus surface finish
  • Glare requirement if the space is an office – UGR target
  • Cut length, packing and annual volume

Where a linear profile goes wrong

Four failures account for most of the linear runs that get complained about, and all four are visible only once the fixture is lit and installed.

Hotspots along the LED pitch

Transmission is not diffusion. If the strip sits too close to the cover or the pitch is too wide, the run reads as a row of dots no matter how good the material is.

Bow between clips

A thin cover supported at long intervals sags under its own weight, and the sag shows as a shadow line. Clip spacing belongs on the drawing.

Visible joints on a continuous run

Cut-length tolerance and end squareness accumulate. Over a long run, small errors become a visible step at every joint.

Glare missed until handover

A linear fixture aimed at a workstation fails on UGR, not on light output. The optical surface has to be chosen against the glare target, not picked for how it looks on a sample card.

These are installation-visible failures, which is why we ask for the LED pitch, the clip spacing and the joint detail before quoting rather than after first-off.

Options we build into the profile

  • Diffuser and housing combined in a single co-extruded section
  • Suspension, clip and end-cap geometry extruded into the profile
  • Prismatic diffusion for low-glare continuous runs
  • Corner and connector solutions for architectural layouts
  • Length cutting and packing by run length
  • Colour consistency controlled across production batches

Frequently Asked Questions

Two things matter: consistent section geometry so the ends match, and controlled cutting so lengths are accurate. We can also design the section so the joint falls in a shadow line.
We control colour batch to batch. For long or phased projects, tell us at the start so we can reserve material and keep the match consistent.
Corner pieces and connector geometry depend on the section. Send the layout and we will tell you what can be extruded and what needs a machined or moulded part.
Cut length is quoted against your requirement – continuous extrusion cut to length. Tell us the length, the tolerance and how the joints are detailed and we will quote to that.
Set the LED pitch and the strip-to-cover distance first, then choose transmission to suit. Diffusion is a function of the gap as much as the material.
Yes. An opaque or structural body with an optical face in the same pass is the usual way to hide the fixings and keep the lit face clean.
We extrude the profile and cut to length. Corner pieces and connectors are normally moulded; send the detail and we will dimension the profile to accept them.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top