LED Strip Lighting Profiles

Extruded profiles that house and diffuse flexible LED strip – channels, covers and lens sections for linear strip installations.

What this application demands from the profile

LED strip is cheap and easy to buy; the profile that houses it is what makes the installation look finished. The channel has to hold the strip, hide the dots, and let the light out – and the cheaper the strip, the more the diffuser has to do.

Dot visibility is the usual problem: closely spaced LEDs at high output show through a clear cover. The fix is a combination of diffusion surface, transmittance and the distance between strip and cover.

LED strip lighting profiles - what we supply
Luminaire typeFlexible LED strip channels, linear strip fixtures, under-cabinet and cove strip
Profile roleChannel, diffuser cover, or lens section over the strip
MaterialsPMMA for diffusion and transmission; PC where impact matters
DiffusionFrosted, opal or prismatic to hide LED dots
SectionU-channel, surface, recessed, corner or custom
LengthCut to length for the installation
AssemblyClip-in covers, end caps and mounting geometry

What we work to

LED strip lighting profile - capability envelope
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Wall thicknessquoted against your drawing
Transmittance0-97%
Surfaceclear, matte, frosted, embossed or prismatic
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Strip profiles are the most price-sensitive category we run, and the most sensitive to two numbers that are rarely supplied: the LED pitch and the gap to the cover.

What LED strip lighting asks of a profile

A strip profile has to do four things at a small scale: hold the tape, get rid of its heat, hide the diodes, and disappear into the surface it is mounted in. The first two are mechanical, the third is optical, and the fourth is a colour and section question. Most failed strip projects failed on the third.

Hotspots are the complaint, and they are a geometry problem. Whether you see a row of dots or a continuous line is set by the LED pitch and the distance from the tape to the cover – transmission alone does not decide it. Send those two numbers with the drawing and the diffusion can be sized to them. Without them, any transmission figure is a guess.

Heat is the second one. Strip tape bonded directly to a profile dumps its heat into that profile, and PC holds shape at temperatures where PMMA starts to move. If the section is the heat path, say so on the drawing – it settles the material faster than any optical argument.

Cost in this category is dominated by section weight per metre and by how much of the profile is optical rather than structural. Co-extrusion is the usual lever: an expensive optical face only where the light passes, and a cheaper structural body everywhere else, in one pass down the same die.

What to put on the drawing

  • LED pitch and distance from tape to optical face
  • Section at 1:1 with the tape channel dimensioned
  • Whether the profile is the heat path
  • Transmittance target as a number, plus surface finish
  • Mounting method – surface, recessed or suspended – and the visible edge
  • Cut length, packing and annual volume

Where a strip profile goes wrong

Four failures account for most strip profiles that get returned, and the first one is the single most common complaint in the category.

Hotspots along the tape

Pitch and gap set whether the run reads as dots. Transmission cannot fix a geometry problem.

Heat build-up in a sealed profile

Sealed sections with no heat path cook the tape. If the profile is the heat sink, it has to be specified as one.

Cover that pops out of a shallow channel

Snap retention depends on wall thickness and material. A channel copied from an aluminium section behaves differently in polymer.

Colour mismatch against the mounting surface

A strip profile sits next to joinery, plaster or metal. Send a physical reference - a screen match is not a match.

Two numbers prevent most of these: the LED pitch and the gap to the cover. Send them with the enquiry.

Profile requirements

  • Diffusion that hides LED dots at your strip pitch
  • Channel geometry that holds the strip without adhesive failure
  • Clip-in covers for service access
  • Corner and connector solutions for continuous runs
  • Cutting and end preparation to installation lengths
  • Clear, frosted and opal options in PMMA or PC

Frequently Asked Questions

Combine the right diffusion surface with the right transmittance and enough distance between the strip and the cover. Tell us the strip pitch and output and we recommend the combination, then confirm it on a sample.
Corner and connector solutions depend on the section. Send the layout and we advise what can be extruded and what is better machined or moulded.
End caps are usually moulded rather than extruded. We can machine simple end preparation and help you source moulded caps for the section.
Set the LED pitch and the tape-to-cover distance, then choose transmission to suit. Both numbers belong in the enquiry.
It can, and in a sealed section it usually has to. Tell us the tape power and whether the profile is the heat path and we will specify the material for it.
Yes – co-extrusion puts the optical face only where the light passes, which is also the usual way to take cost out of a strip profile.
From 500 pcs per profile, around six weeks from drawing to production including tooling.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top