Applications

Where our lighting profiles are used – from linear and architectural systems to industrial, troffer, strip, office and signage lighting.

What we work to

Application environments - capability envelope
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Transmittance0-97%, matched to the target
FlammabilityUL94 V-0 from 1.0 mm, V-2 down to 0.40 mm - material grade
IngressIP65 / IP66 / IP67 by section and gasket design
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Applications are not product categories – they are environments. The environment is what decides material, grade and section, which is why it belongs in the first enquiry rather than in the last email.

How to specify by environment

The fastest way to a correct specification is to describe where the fitting lives before describing what it looks like. Impact, heat, UV exposure, cleaning regime, ingress requirement and any compliance file – those six answers settle material and grade, and usually the section as well.

Office and commercial interiors are decided by glare. A fitting can meet its output target and still fail the space if the optical surface lets the source into view, which pushes the choice towards prismatic and micro-prismatic faces rather than plain diffusion, at some cost to transmission.

Industrial, transport and outdoor work is decided by survival. Impact and heat point to polycarbonate; ingress protection is achieved by the section and the gasket working together rather than by the material; and a flame rating – the grades we run reach UL94 V-0 from 1.0 mm and V-2 down to 0.40 mm – belongs to the material at a stated thickness, not to the finished luminaire.

Architectural and signage work is decided by appearance and uniformity. Colour match, surface consistency and even illumination across the face outrank raw output, and those are held by physical references, retained samples and – for signage – by getting the box depth and LED pitch right before the material is chosen.

What to put on the drawing

  • Where the fitting is installed, and what it is exposed to
  • Impact, heat and cleaning regime
  • Required IP rating and the gasket interface that will deliver it
  • Glare target for worked-in spaces – UGR where it applies
  • Transmittance target as a number at the running wall thickness
  • Colour reference – RAL, Pantone or a physical chip

Where application specification goes wrong

Four mistakes account for most application-driven re-specifications, and every one of them comes from describing the part before the environment.

Environment left out of the enquiry

Without exposure, temperature and cleaning regime, the material gets selected on optics alone - and usually wrong.

Ingress quoted without a gasket design

IP ratings come from the section and the seal together. Without the interface on the drawing, the rating can only be tested, not engineered.

Glare discovered at handover

A diffuser chosen on output alone can fail a UGR assessment in an office or a classroom.

Colour matched to a screen

A colour picked from a monitor is not a colour. Send a reference, and ask for a retained sample if the project will be re-ordered.

The environment paragraph of your enquiry is the most valuable one in it. Send it first and most of the specification follows.

Questions we get asked

Which application do you supply most?

Commercial and office interiors, followed by industrial and architectural work. The capability envelope is the same for all of them - the environment changes the specification, not the line.

Can you help choose the material?

Yes. Send the environment - impact, heat, exposure, cleaning and any compliance requirement - and the material question usually answers itself.

Do you supply profiles for outdoor use?

Yes. UV-stabilised grades and UV-capped co-extrusion are available; which one depends on the exposure and the service life you need.

What is the minimum order and lead time?

From 500 pcs per profile, around six weeks from drawing to production including tooling.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top