PC LED Diffuser Profiles

Polycarbonate diffuser sections for LED luminaires that also have to survive impact – the optical performance of a diffuser with the toughness of PC.

What we supply

Most diffusers are acrylic because acrylic transmits more light. But in industrial, transport and public-area luminaires the diffuser is also a cover – it has to take impact – and that pushes the material decision to polycarbonate.

The engineering task is to get acceptable diffusion and transmission out of PC without giving up the impact performance that made you choose it. We tune surface structure, wall thickness and grade together.

PC LED diffuser profile - capability
MaterialPolycarbonate (PC), UV-stabilised and FR grades available
Key propertyImpact resistance combined with diffusion
DiffusionFrosted, opal, matte, prismatic
TransmittanceSet to your target and confirmed on prototypes
Typical fittingsIndustrial, tri-proof, transport and public-area luminaires
Wall thicknessSet to the impact requirement
ProcessExtrusion and co-extrusion
LengthCut to your fixture length

What we work to

PC LED diffuser profile - capability envelope
Section widthup to 400 mm across the diffuser
Wall thicknessfrom 1.0 mm where UL 94 V-0 is required on the PC grades we run
Flame ratingUL 94 V-0 from 1.0 mm, V-2 down to 0.40 mm, per the UL component plastics cards
Transmittancetuned to your target - expect a few points below an equivalent PMMA part
Impactthe reason to choose PC: covers that get struck without cracking
Surfacematte, frosted, embossed or prismatic
Colouropal, clear or matched to RAL / Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

The honest framing of a PC diffuser is a trade: a few points of transmission and some UV stability given up in exchange for impact resistance and a flame rating. Whether that trade is worth it depends on where the fixture goes, not on which material is “better”.

When a PC diffuser is the right answer

A polycarbonate diffuser is what you specify when the part has to survive something. High bays that get hit by a scissor lift, tri-proof fixtures washed down with a hose, transit and industrial fittings where vibration and knocks are normal, vandal-resistant bulkheads – in all of those the diffuser is the most exposed component in the assembly, and acrylic will crack where polycarbonate dents and holds.

The second reason is flame performance. Where the luminaire has to carry a rating and the diffuser is part of the assembly, PC gives you a route to V-0 at 1.0 mm that PMMA does not. That single fact often decides the material before optics are discussed at all: it does not matter how well an acrylic diffuser transmits if the fixture cannot be certified with it.

What you give up is measurable but smaller than buyers usually fear. PC transmits a few points less than PMMA in the visible range, and standard grades drift towards amber under UV unless they are stabilised. Both are manageable: the first by specifying the transmittance number you need so the compound is tuned to hit it, the second by using a UV-stabilised grade or co-extruding a stabilised face. Neither is a reason to accept a failing part, and neither is free.

The specification work is the same as any diffuser plus one extra item: state the flame rating and the thinnest wall, because those two together decide which grades are available to you. After that it is transmittance at a stated thickness, LED pitch and clearance, surface, and the fit to the housing. Get the rating and the wall settled first – everything else can be tuned, that pair cannot.

What to put on the drawing

  • Flame rating required, and the thinnest wall in the section
  • Transmittance target as a number at that wall thickness
  • LED pitch and the clearance from LED to diffuser
  • Whether the fixture is exterior or washed down – drives the UV grade and surface
  • Impact requirement, so the wall is not drawn thinner than the use demands
  • Fit to housing at 1:1, cut length and packing

Where a PC diffuser goes wrong

The failures are different from acrylic ones because the material fails differently: it does not crack, it discolours and it stresses.

Amber drift on unstabilised grades

Standard PC yellows under UV faster than acrylic does. An exterior PC diffuser without a stabilised grade or a stabilised co-extruded face will change colour within a service life, and no amount of process control prevents it.

A rating assumed rather than read

V-0 at 1.0 mm is a material property recorded on the UL card. It does not transfer automatically to a finished profile with a different wall, and it is not a certificate for the luminaire. Read it against your thinnest wall before specifying.

Transmission budget eaten twice

PC starts a few points behind PMMA, and a dense diffusing compound takes more. Buyers who specify "opal PC" and then chase the lumen target end up with a fixture that cannot reach it. State the number and let the compound be tuned to it.

Stress marks at the fit

PC takes more force to assemble and remembers it. A tight snap onto a stiff housing leaves whitening that becomes a crack site under vibration. Radii and undercut depth are the fix, decided on the drawing.

For industrial and exterior work the trade is usually worth making, because a cracked diffuser takes the whole fixture out of service while a slightly dimmer one does not. The point is to make the trade deliberately rather than discover it after the first installation.

Options we build into the profile

  • Diffusion tuned to hide LED pitch while keeping PC toughness
  • UV-stabilised and flame-retardant PC grades
  • Prismatic surfaces for glare-controlled industrial fittings
  • Thick-wall sections where impact resistance is critical
  • Co-extrusion with a PMMA diffusing layer for higher transmission
  • Cutting, drilling and packing to your assembly requirements

Frequently Asked Questions

PMMA transmits more light, but where the diffuser is also the cover – industrial, transport or public-area fittings – impact resistance usually decides it. PC is the safer choice there.
Diffusion is a function of surface structure and material grade as much as base polymer. We tune both to reach the diffusion and transmission you need.
Co-extrusion is often the answer: a PC body for strength with a PMMA diffusing layer for optical performance.
Neither is better in the abstract. PMMA transmits more and resists UV yellowing; PC survives impact and carries a flame rating. Choose by the failure you cannot accept: a cracked diffuser in an industrial fitting, or a few points of light in an office fixture.
A few points in the visible range, depending on grade and wall thickness. It sounds small until the fixture is already at its lumen target. The practical fix is to state the transmittance you need and have the compound tuned to hit it, rather than comparing generic material figures.
Yes, with a UV-stabilised grade or a stabilised co-extruded face. Unstabilised PC will drift towards amber under daylight. Tell us at quotation that the part is exterior and the grade selection changes with it.
The UL 94 rating is a property of the material grade at a stated thickness, recorded on the UL component plastics card. It is not a certification of the extruded part or of the luminaire. We can hold the wall thickness the rating needs and supply the material documentation; certifying the assembly is the luminaire maker’s step.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top