Optical Lighting Profiles

Extruded sections engineered for what the light does – diffusion, beam shaping and glare control – rather than only for the shape of the fitting.

What we supply

An optical profile is specified by performance, not just by dimensions: transmittance, beam angle, glare rating, and how uniformly the lit surface looks. That means the section geometry, the surface structure and the material all have to be designed together.

We work from your optical target – tell us the transmittance, the beam spread and any UGR requirement – and design the section and surface to reach it. Prototypes are measured before tooling is finalised.

Optical lighting profile - capability
FunctionDiffusion, beam shaping, glare control, light guiding
MaterialsPMMA for maximum transmission; PC where impact matters
Surface structuresFrosted, matte, prismatic, embossed, lens geometry
TransmittanceSet to your optical target and confirmed on prototypes
Beam controlLinear lens geometry shapes the beam without secondary optics
GlarePrismatic and micro-prism structures for UGR-controlled luminaires
ProcessExtrusion and co-extrusion
VerificationPrototype sections produced for optical approval

What we work to

Optical lighting profile - capability envelope
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Optical geometryprismatic, lenticular, embossed or plain - held by die condition
Transmittance0-97%
Surfaceclear, matte, frosted, embossed or prismatic
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Optical profiles are the one category where the die, not the drawing, sets the result. Fine geometry is the first thing a die loses, so optical performance is held by die maintenance intervals rather than by a tolerance callout.

How to specify an optical lighting profile

“Optical” covers three different jobs that get quoted as one: a diffuser that spreads light, a lens that directs it, and a prismatic surface that controls glare. They share a material and a process and almost nothing else. Being clear about which one you need is the difference between a first-off that works and three rounds of samples.

A diffuser is judged on two numbers – how much light gets through and how well the source is hidden. A lens is judged on where the light lands, which makes the geometry of the face the critical feature rather than the material. A prismatic surface is judged on glare, and it is the most demanding of the three to hold over a long run, because the prisms are small and they are the first detail to soften as a die wears.

The material split follows from that. PMMA replicates fine prism geometry more cleanly and holds its colour; PC is specified where impact or heat enters the picture. Co-extrusion covers the case where both matter, at the cost of a more demanding die and a longer first-off check.

What the drawing has to carry is the optical intent, not just the section. Give us the beam goal or the glare target, the LED pitch and its distance from the optical face, and the transmission you need at the wall you are running. Without the pitch and the gap, optical geometry is guesswork.

What to put on the drawing

  • Optical job: diffuse, direct, or control glare
  • Section at 1:1 with optical geometry dimensioned
  • LED pitch and distance from the source to the optical face
  • Transmittance target as a number at the running wall thickness
  • Glare or beam target where one applies – UGR, beam angle
  • Run length and annual volume, for die maintenance planning

Where an optical profile goes wrong

Four failures account for most of the optical parts that come back, and three of them are optical rather than mechanical.

Prism detail fading across a long run

Fine geometry is the first thing a die loses. If the beam angle drifts over a production run, the cause is usually die wear and the fix is a maintenance interval, not a material change.

Optics specified without the LED pitch

Diffusion depends on the distance from the source to the face as much as on the material. Without the pitch and the gap, transmission numbers do not predict hotspots.

Glare discovered at handover

A prismatic face chosen for looks can fail a UGR target. The surface has to be selected against the glare requirement, not against a sample card.

Optical face damaged in handling

The face that controls the light is the face that gets scratched. Surface protection and packing have to be specified with the part, not after it.

Optical performance is a process result, not a drawing result. It is held by die condition, measurement at intervals, and a retained sample from each batch.

Options we build into the profile

  • Prismatic and micro-prism surfaces for glare-controlled luminaires
  • Linear lens geometry that replaces secondary optics
  • Diffuser grades tuned to hide LED pitch at a target transmittance
  • Co-extruded structures combining optical and mechanical zones
  • Light-guide sections for edge-lit applications
  • Prototype measurement before production tooling release

Frequently Asked Questions

Tell us the target UGR and the luminaire layout. Glare is controlled with prismatic or micro-prism surface structures, and we confirm the result on prototype sections before releasing production tooling.
We verify appearance, dimensions and transmittance on prototypes. Where a formal photometric report is required, we coordinate testing with the fixture manufacturer or a nominated laboratory.
In many linear luminaires, yes – an extruded lens profile shapes the beam without a separate optic, which reduces parts and assembly cost.
A diffuser spreads light and hides the source. An optical profile is the wider category – it also covers lenses that direct light and prismatic surfaces that control glare.
Yes, by die maintenance interval rather than by tolerance alone. Prisms are the first detail to soften as a die wears, so the run length matters when we plan the tooling.
PMMA for fine prism geometry and long-term colour stability; PC where impact or heat is in play. Co-extrusion covers both at once.
It helps. For optical work a physical sample with the beam result you are getting today is more useful than a drawing, because optical geometry is measured, not described.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top