Request a Quote

Send us the drawing, sample or specification. Our engineers review profile geometry, material and tooling feasibility and come back with a proposal and quotation.

Upload your drawing: PDF, DWG, DXF, STEP or IGES files up to 20 MB. Prefer email? Send it to info@leddiffuserfactory.com.
[contact-form-7 id="13" title="Engineering RFQ Form"]

What we work to

Enquiry to production - what the numbers are
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Transmittance0-97%, matched to your target
Colour100+ shades matched to RAL or Pantone
FlammabilityUL94 V-0 from 1.0 mm, V-2 down to 0.40 mm - material grade
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included
Quotation turnaroundthe section, wall and optical target decide it - see below

These are the limits of the line, not a catalogue. Nothing on this site is a stock item: every profile is quoted against a drawing or a sample.

What to send to get a quote that holds

A quotation for a custom extrusion is only as good as the information behind it. Most of the difference between a quote that holds and one that gets revised is not price – it is whether the section, the wall thickness and the optical target were stated. Those three decide the die, the haul-off and the run speed, and without them any number is provisional.

The fastest enquiry is a drawing plus a sample. The drawing gives intent, and the sample gives the truth: wall thickness on an existing extruded or moulded part is rarely what the drawing claims. If you are replacing a profile you already buy, send a cut length and tell us the transmission and colour you are getting today. We measure the section and quote against the real geometry.

If there is no sample yet, the drawing still has to carry the optical intent. Transmission is not diffusion: asking for “opal” gives a family of results anywhere from a soft 60% to a bright 85%, and the difference shows up as either a hotspot or a dim fixture. Give us the number you are aiming for at the wall thickness you are running, plus the LED pitch and the distance to the cover if you know them.

Volume and timing come last and matter more than people expect. Annual volume sets how the die is built and how the run is scheduled; a stated target date tells us whether tooling or finishing is the critical path. Both belong in the first message.

What to put on the drawing

  • Section at 1:1, with wall thickness dimensioned separately
  • Material preference, or the environment if you are not sure
  • Transmittance target as a number at the running wall thickness
  • Colour reference – RAL, Pantone or a physical chip
  • Annual volume, target date and cut length
  • A physical sample if the part already exists

Why quotes get delayed or revised

Four gaps account for most of the enquiries that go back and forth, and all four are closed in the first message.

No wall thickness on the drawing

Wall thickness drives material cost, cooling time and snap behaviour. Without it, a quote is an estimate rather than a price.

Optical target written as a colour word

"Opal", "frosted" and "milky" span a wide transmission range. Without a number, first-off approval becomes an argument and a second sample costs three weeks.

Tolerance inherited rather than chosen

A blanket tight tolerance across the whole section forces a slower line and hand-finished tooling for dimensions that carry no function. Mark the features that matter.

Volume not stated

Volume sets die construction and run scheduling. Without it, the price quoted is for a run size nobody has agreed to.

Every one of these is a paragraph in the first email. Send them and the quote you get back is the quote you build to.

Questions we get asked

What is the minimum order quantity?

From 500 pcs per profile. Below that, line changeover and first-off checking dominate the cost.

How long does a new profile take?

Around six weeks from drawing to production including tooling. First-off approval is part of that schedule, not an afterthought.

Can you quote from a sample alone?

Yes, and it is usually the fastest route. Send a cut length plus the transmission and colour you are getting today.

Do you charge for tooling?

Tooling is quoted with the profile and is included in the six-week figure. It is built for your section and maintained for the life of the part.

What Happens Next

  1. Engineering review – we check extrudability, wall thickness and optical targets.
  2. Material proposal – PC, PMMA, co-extrusion or a specified compound.
  3. Tooling plan – die design and lead time for your section.
  4. Quotation – piece price, tooling cost and sample lead time.
  5. Prototype – first-off sections for your approval before production.

Direct Contact

Contact details
CompanyZhejiang Baoming Optical Materials Co., Ltd.
Emailinfo@leddiffuserfactory.com
Telephone+37259205909
WhatsApp / WeChatWhatsApp: +37259205909 · WeChat: +8615867897761
AddressNo. 9 Zhongnan Hi-Tech, Xin'an Town, Deqing County, Huzhou City, Zhejiang Province, China 313200
Response timeWithin 24 working hours
Scroll to Top