PMMA Light Covers

Acrylic light covers with high transmission and long-term colour stability – for decorative, architectural and general lighting where the cover is seen.

What we supply

Where the cover is part of the design rather than just protection, acrylic is usually the right material. It transmits more light, it holds a cleaner surface, and it does not yellow the way standard polycarbonate can over time.

We extrude PMMA covers in flat, curved, half-round and custom sections, with opal or frosted diffusion where the light source should not be visible, and clear where it should.

PMMA light cover - capability
MaterialPMMA (acrylic), UV-stable grades
Key propertyHigh light transmission and UV stability
Typical fittingsDecorative, architectural, commercial and residential luminaires
FormFlat covers, half-rounds, tubes, custom sections
SurfaceClear, opal, frosted, matte, prismatic
TransmittanceSet to your optical target
ColourClear, opal, tinted or matched to RAL / Pantone
LengthCut to length to your specification

What we work to

PMMA light cover - capability envelope
MaterialPMMA (acrylic), UV-stable optical grades
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Wall thicknessquoted against your drawing
Transmittance0-97%, tuned to the fixture rather than to a default
Surfaceclear, matte, frosted, embossed or prismatic
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Acrylic is chosen for how it carries light and for how long it keeps carrying it. The trade is impact – where a cover can be struck, say so on the drawing and the conversation moves to PC or to co-extrusion.

How to specify a PMMA light cover

A light cover is doing two jobs that do not agree. It has to pass as much light as the photometric calculation assumes, and it has to hide what is behind it. Push transmission up and the LEDs become visible; push diffusion up and the fixture gets dim. The whole specification is that trade, and it cannot be resolved by picking a material off a list.

PMMA is usually the right side of that trade. It transmits more in the visible range than polycarbonate, it is among the most UV-stable optical plastics available, and it replicates fine prism geometry cleanly. That is why prismatic diffusers and linear lenses are normally quoted in acrylic rather than PC.

What it does not do is take a knock. Acrylic is the more brittle of the two, and it loses impact strength as temperature drops – a cover that survived summer handling can crack in a winter container. Where the fixture is low-mounted, in a corridor, on transport, or anywhere a ladder or a trolley can reach it, the usual answer is either PC or a co-extrusion with a PC structural layer behind an acrylic optical face.

On the drawing, the single most useful number is the transmittance target at the wall thickness you are actually running. “Opal” spans a wide range and turns first-off approval into an argument. Give us a number, a surface description and a colour reference and the sample comes back close enough to approve in one pass.

What to put on the drawing

  • Section at 1:1 with wall thickness dimensioned separately
  • Transmittance target as a number at that wall thickness
  • Diffusion requirement: how well the LED source has to be hidden
  • Impact and cleaning regime the cover has to survive
  • Surface: clear, matte, frosted, embossed or prismatic
  • Cut length, packing and annual volume

Where a PMMA light cover goes wrong

Four failures account for most of the acrylic covers that come back, and all four are decided before the first metre is pulled.

Stress cracking at the snap

An undercut that is too aggressive for acrylic forces the wall further than it wants to go, and the crack appears weeks later. Check the undercut against wall thickness before the die is cut.

Yellowing that is not UV

Not every yellow part is a UV failure. Running the melt too hot degrades the resin on the way out and the colour is already in the profile at take-off.

Brittle failure in cold transit

Acrylic loses impact strength as it gets colder. Packing has to be specified for the shipping route, not for the factory floor.

Transmission measured on the wrong thickness

Transmission is thickness-dependent. A number measured on a 3 mm sample is not the number you get at 1.5 mm, and the difference is visible in the photometric result.

None of these show up on a datasheet. They show up in first-off inspection and in the field, which is why we keep a retained sample from each batch rather than relying on a certificate alone.

Options we build into the profile

  • Opal and frosted diffusion at a defined transmittance
  • Tinted acrylic for decorative luminaires
  • Prismatic surface for glare-controlled decorative fittings
  • Curved and half-round sections
  • Protective film to keep surfaces clean through assembly
  • Cutting, drilling and machining to your drawing

Frequently Asked Questions

Yes. Acrylic is the common name for PMMA. For lighting covers the two terms are used interchangeably.
PMMA is one of the most UV-stable optical plastics and resists yellowing far better than standard polycarbonate, which is why it is used for covers that stay visible.
Yes. Send a sample and we match the colour and transmission, then confirm on a prototype section.
Yes. PMMA is poly(methyl methacrylate), acrylic is the trade name. A “PMMA light cover” and an “acrylic light cover” are the same part under two names.
The one your photometric calculation assumes, at the wall thickness you are running. The line covers 0-97%, so your target – not our default – is the starting point.
Acrylic is among the most UV-stable optical plastics, but no plastic is immune. Process temperature and the grade both matter, which is why we control both rather than relying on the datasheet.
Yes, by co-extruding a PMMA optical face onto a PC structural layer in one pass. You keep the light quality of acrylic and gain most of the toughness of PC.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top