Architectural Lighting Profiles

Extruded profiles for coves, reveals, facades and decorative runs – where the profile is part of the architecture and has to look right as well as perform.

What this application demands from the profile

Architectural lighting is unforgiving because the profile is seen. Surfaces have to be clean, corners and joints have to line up, and colour has to be consistent along a run that may cross several walls.

The sections are also more varied than in commercial lighting: coves, asymmetric wall-wash sections, recessed reveals and custom decorative shapes all appear, and most are one-off designs.

Architectural lighting profiles - what we supply
Luminaire typeCoves, reveals, wall-wash, facade and decorative runs
Profile roleDiffuser, housing, trim, or a decorative visible section
MaterialsPMMA for clarity and UV stability; PC where impact or heat matters
SurfaceClear, matte, frosted, tinted or prismatic
GeometryAsymmetric and custom sections developed to your drawing
ColourClear, opal, tinted or matched to RAL / Pantone
EnvironmentUV-stabilised grades for daylight-exposed profiles

What we work to

Architectural lighting profile - capability envelope
MaterialPC or PMMA, single extrusion or co-extruded
Section widthup to 400 mm across the profile
Critical die dimensions±0.1 mm on the dimensions that carry the fit
Wall thicknessquoted against your drawing
Transmittance0-97%
Surfaceclear, matte, frosted, embossed or prismatic
Colour100+ shades matched to RAL or Pantone
Minimum orderfrom 500 pcs per profile
Sample to mass productionaround 6 weeks, tooling included

Architectural work is the most demanding category on the site, because the profile is visible when the light is off. Colour consistency and surface finish carry as much weight as the optics.

What architectural lighting asks of a profile

In architectural work the profile is part of the finish. It is seen in daylight, at close range, next to materials that were chosen by somebody with a strong opinion. That moves the specification: colour match, surface consistency and the neatness of the visible edge matter as much as transmission does.

Colour is the recurring problem. An anodised aluminium trim, a painted ceiling and an extruded polymer profile are three different colour systems, and they drift differently over time. Send a physical reference rather than a screen image, and tell us what the profile is sitting next to. We match across 100+ shades to RAL or Pantone, and we keep a retained sample so a re-order two years later is matched to the first production run rather than to a fresh mixing.

Optically, architectural work usually wants either a soft continuous line or a controlled beam, and both are geometry problems before they are material problems. Prismatic and lenticular faces give control that plain diffusion cannot, and PMMA replicates that fine geometry more cleanly than PC does.

The other thing architectural work asks for is the awkward detail: corners, returns, recessed shadows and hidden fixings. Those are usually solved in the section – a co-extruded opaque body with an optical face keeps the fixings out of sight and the lit edge clean.

What to put on the drawing

  • Section at 1:1, including the visible edge and shadow gap
  • Colour reference – physical chip, RAL or Pantone – and what it sits beside
  • Surface finish on the visible face
  • Optical intent: soft continuous line or controlled beam
  • Corner, return and fixing detail
  • Cut length, packing and annual volume

Where an architectural profile goes wrong

Four failures account for most architectural profiles that get rejected, and three of them are visible with the light switched off.

Colour matched to a screen or a name

A colour picked from a monitor or a written colour name is not a match. Physical references and retained samples are what make a re-order match the original.

Visible fixings in a clean shadow gap

Fixings that look fine on a sample become obvious in a recessed detail. Co-extruded opaque bodies hide them without a secondary part.

Surface damage on the visible face

The face everyone looks at is the face that gets scratched in transit. Protective film and packing have to be specified with the part.

Prism geometry lost over a long run

Fine optical detail is the first thing a die loses. Beam control is held by die maintenance intervals, not by a tolerance callout.

Architectural profiles are approved by eye. That makes the retained sample and the first-off approval the two most important documents in the job.

Profile requirements

  • Custom and asymmetric sections developed from your drawing
  • Clean optical surfaces free of flow lines and die marks
  • UV-stable material for daylight-exposed runs
  • Colour consistency across a project and across reorders
  • Corner and connector solutions for architectural layouts
  • Protective packing so surfaces arrive unmarked on site

Frequently Asked Questions

Yes. Asymmetric sections are common in architectural work. Send the beam requirement and the section you have in mind and we engineer it for extrusion.
Corner pieces depend on the section. Send the layout and we advise what can be extruded, what needs machining, and what is better handled as a moulded part.
Optical and decorative surfaces are protected with film and packed to keep them clean and unmarked through transport and site handling.
Yes – across 100+ shades to a RAL or Pantone reference. Send a physical chip where one exists, and tell us what the profile sits beside.
Retained samples from each batch, measured under the production record. Re-orders are matched to the retained sample, not to a fresh mix.
Usually, by co-extruding an opaque or structural section alongside the optical face in the same pass.
From 500 pcs per profile, around six weeks from drawing to production including tooling.

Send us your drawing or sample

Our engineers review geometry, material and tooling feasibility and come back with a profile proposal and quotation.

Or email your drawing to info@leddiffuserfactory.com · WhatsApp +37259205909 · WeChat +8615867897761

Scroll to Top